NNHV 8123

NNHV 8123

High Voltage LISN acc. to CISPR 25 Ed. 4 or BMW GS 95025-1 to measure the conducted disturbance voltage on shielded lines for (hybrid) electric vehicles (HEV, EV), can be used for BCI with an external dummy load,

impedance (5µH) || 50 Ohm. 70 (100) A, 1000 V DC. Backside with built in

0.1 microfarad capacitor to ground, N-jack. Normally used in pairs inside the enclosure HVSE 8600!

NNHV 8123-200

High Voltage LISN acc. to CISPR 25 Ed. 4 or BMW GS 95025-1 to measure the conducted disturbance voltage on shielded lines for (hybrid) electric vehicles (HEV, EV), can be used for BCI with an external dummy load,

impedance (5µH) || 50 Ohm. 200 A, 1000 V DC. Backside with built in

0.1 microfarad capacitor to ground, N-jack. Normally used in pairs inside the enclosure HVSE 8600!

NNHV 8123-400

High Voltage LISN acc. to CISPR 25 Ed. 4 or BMW GS 95025-1 to measure the conducted disturbance voltage on shielded lines for (hybrid) electric vehicles (HEV, EV), can be used for BCI with an external dummy load,

impedance (5µH) || 50 Ohm. 400 A, 1000 V DC. Backside with built in

0.1 microfarad capacitor to ground, N-jack. Normally used in pairs inside the enclosure HVSE 8600!

NNHV 8123-800

High Voltage LISN acc. to CISPR 25 Ed. 4 or BMW GS 95025-1 to measure the conducted disturbance voltage on shielded lines for (hybrid) electric vehicles

(HEV, EV), can be used for BCI with an external dummy load, impedance (5µH)||50 Ohm. 800 A, 1000 V DC. Backside with built in

0.1 microfarad capacitor to ground and suitable discharge resistor, N-jack. To be used in pairs inside a shielded enclosure HVSE 8601!

HVSE 8600

Shielded housing for 2 HV-LISN, 2 paths with cable feed throughs for HV+ and HV-, shield can be connected to the housing, 2 measurement ports N, 1 monitor port N, with connecting cables between inside measurement ports and outside N-connectors. All models of the NNHV- and NNBM-series can be inserted. For full CISPR 25 Ed. 4 compliance a modification of the back side circuitry of the NNBM series is required!

Opt. 8600-blanco

1 pair of flange panels for HVSE 8600. Mains side with no connector or feed through. DuT side with only 2 x N-feed throughs for AUX and 2 x N feedthroughs for RF-HV+ and RF- HV-. Feed throughs for HV+ and HV- must be drilled and assembled by customer.

Opt. 8600-100

1 pair of flange panels for HVSE 8600 with cable feed throughs for shielded cables up to ca. 100 A.

Opt. 8600-200

1 pair of flange panels for HVSE 8600 with cable feed throughs for shielded cables suitable for max. currents in a range of ca. 100 A to 200 A.

Opt. 8600-400

1 pair of flange panels for HVSE 8600 with cable feed throughs for shielded cables suitable for a range of ca. 200 A to 400 A.

HVSE 8601

Shielded housing for 2 units of HV-LISN NNHV 8123-800, with cable feed throughs for HV, shield can be connected to the housing, 2 measurement ports N, 2 monitor ports N, with connecting cables between inside measurement ports and outside N-connectors.

Opt. 8601-800

1 pair of flange panels for HVSE 8601 with cable feed throughs for shielded cables suitable for a range of ca. 400 A to 800 A.

HV-LISN acc. to ECE R10.06, CISPR 12 and PSA-1

NNHV 8123-400R

High Voltage LISN acc. to CISPR 25 Ed. 4 or BMW GS 95025-1 with C2=0.1 microfarad switchable to ECE R10 with C2=1.0 microfarad to measure the con- ducted disturbance voltage on shielded lines for (hybrid) electric vehicles (HEV, EV), can be used for BCI with an external dummy load, impedance (5µH) || 50 Ohm. 400 A, 1000 V DC. Backside with built in 0.1/1.0 microfarad capacitor switchable, N-jack. Normally used in pairs inside the enclosure HVSE 8600!

CAP 0.9-400

0.9 microfarad capacitor built into an adapter, which can be applied to the mains terminals of the NNHV 8123-800 or NNHV 8123-400 for the standards ECE R10.06, CISPR 12 and PSA 9829, 9831